Mini size CellRetention™ keep HFF free from fouling

World only P-SUB including ATF method offer:

• HFF (Hollow-Fibre-Filter) fouling free process with innovative diaphragm pump
• 100 – 250 ml Working Volume fully pre-assembled P-SUB
• Alternating of broth by Thalia TM80 diaphragm Alternating-Single-Use-Pump (A-SUP)
• Outstanding Clotho software - stand-alone or OPC-UA connected

Industry leading architecture P-SUB pre-installed with:

• Direct-Fit / integrated HFF (Hollow-Fibre-Filter) eliminating the shear stress caused by the restricting Luer-Loc design
• Ground-breaking LASER sensor controlled diaphragm Single-Use-Pump (A-SUP)
• Single-Use-Sensors (SUS) for DO, pH, temp, level

BIG

CellRetention-500 complete

BIG

CellRetention-500 in HSF and Clotho

BIG

CellRetention-500 SUS details

Right photo show with VisiFerm installed the position of the VisiWell (VisiFerm not included). Center photo P-SUB mounted in Heating-Support-Foot. The HSF helps stabilize the un-balanced weight distribution and improve temperature accuracy. Red LASER sensor mounted in a Re-Usable-Bracket above the dome of the Thalia TM80/30 A-SUP. Clotho controllers require only the cable to the Laser sensor and the blue pneumatic hose to drive the Thalia A-SUP. Right photo show vertical arranged Thalia directly coupled to the HFF for minimum dead volume.

General features of CellRetention™ small size P-SUB:

• No space consuming servo motor attached to the head plate - take advantage of Magnetic-Bottom-Drive (MBD)
• Designed with 3 x head plate ports and 6 ports for In&Out with small diameter hoses in weldable length 
• Exchanged broth volume fully programmable and obtained velocity all accurately measured – no guessing
• Integrated HFF with pore 0.2 µm, 14 x 1.0 mm PES straw/lumen, ?? cm2 area, Luer-Lok ports, (D0?-P20U-10-N)
• The complete and pre-assembled P-SUB unit packed in dual film bags and precision irradiated – forget the autoclave
• SUB dim is OD 82 x 120 mm for Working Volume (WV) ranging from 100 ml up to 400 ml
• Thermal control with the – Heating-Support-Foot (HSF) available for 110 VAC or for 230 VAC

Further P-SUB size 500 features:

• Comes with Magnetic-Bottom-Drive (MBD) for up to 250 RPM on Magnetic-Stirrer-Table (MST)
• Pitch blade impeller - you an choose blade design, number blades, angle, diameter, etc
• 2 x small diameter weldable hoses length 600 mm
• 1 x small short hose with 5 cm2 sterile filter for aeration via a 20 µm micro porous sparger body
• 1 x small short hose with swabable valve for bottom sampling
• 1 x exhaust gas hose with 16 cm2 sterile filter 
• Need for electrical thermal control = Heating-Support-Foot (HSF)

BIG

SUS in CellRetention-500 closeup

BIG

Direct-Fit HFF to Thalia

BIG

CellRetention 500 in HSF

DO, pH mounted in the 3 port head plate - one PG13 free. If needed the otherwise standalone Thalia A-SUP can fixed to the P-SUB headplate. Center photo – Direct-Fit HFF to scalable Thalia for better flow performance and lower shear stress. The small size TM80 with NO Luer-Lock but direct HFF connection to both deep-tube and TM80.

The 4 available head plate ports are used for:

1. One port occupied by OneFerm or FermProbe pH Single-Use-Sensor (SUS) S8 classical signal
2. One port occupied by VisiWell Single-Use-Well (SUW) designed for VisiFerm (RUS) 120 mm DO sensor
3. One free port